SMITH UNDERTAILGATE SPREADER

SMITHUTG
SMITHUTG Smith Spreaders Smith Spreaders

The Smith Under Tailgate Series of Spreaders are designed for low-maintenance high torque drive. Built with in a 96” length, easily installed on your Dump Body or Truck. This gives you the best of both worlds, allowing you to retain the use of the truck without removing the spreader. Just put the lid up to use as ice control and put the lid down for full use of the truck. The variety of choices is a key ingredient with this design, Hydraulic Direct Drive, Gear Box Drive, Chain Drive, or Electric. Using our consistent 304 Stainless-Steel construction, durability is never the issue. Our UT Series uses a screw auger cross conveyor, self-leveling, and a full drop trough for easy cleanout.

Fits: Dump Trucks, Municipal Vehicles
Hopper Material: Stainless Steel

Please contact us for more information about this product.

Request a Quote


Share this product:

Standard Features on all Undertailgate Spreaders:

All 304 stainless steel construction

  • 3/16″ stainless-steel hopper.

  • 7 ga stainless-steel cover.

  • 2 channel design running full length with offset spinner assembly mounting brackets.

  • Trough Bottom assembly.

  • 3/16” full drop design with offset hinges, stainless-steel safety stop easy latch handles for easy cleanout- one-person operation

  • Trough end plates – 3/16“ plate complete, cutouts for top cover latches, bottom trough latches, chain, lifting eyes, bearing, motor, and gearbox mounting plates.

  • 2 ply rubber belt type. **Only on rubber trough under tailgate. **

  • Spinner assembly, self-leveling, swing away type, all-in-one fully adjustable assembly.

  • 20″ dia. polyurethane spinner disc. – Standard Units only.

  • Molded Non-directional flights.

  • Minimum 10″ horizontal adjustment & minimum of 8″ vertical adjustment.

  • Ability to fully swing out to clear full bottom drop trough when open.

  • Auger flighting supported by HD industrial malleable iron 2-hole flange ball bearings.

Drive Options:

  • Hydraulic drive – high torque hydraulic motor directly couples to auger.

  • Gearbox drive – 5:1 reduction gearbox coupled directly to the auger by a hydraulic motor.

  • Chain & sprocket drive – # 60 roller chain drive directly couples the auger to the hydraulic motor.

  • Electric drive – two 12 volt motors one operates the spinner, and one operates to drive the auger.

  • Electric drive comes standard with the dual electric speed control and fail-safe switch.

  • 4″ auger – 1-1/4″ schedule 80 pipe with 4″ OD auger.

  • Molded non-directional auger flighting.

  • Wiring kit.






Standard Hydraulic Features:

(includes; gearbox drive, direct drive & chain drive)

  • Auger flighting – 6″ diameter with 3/8″ thick flighting mounted to 2″ schedule 80 pipe complete with 1-1/4″. dia. stub shaft uhmw expansion bushings inside pipe ends.

  • See manual for additional specs.

ADDITIONAL OPTIONS & ACCESSORIES:

  • Available in standard bi-directional.

    • Continuous flight & reverse solid flight available (additional cost possible).

  • Self-Leveling Weight Attachment

  • Discharge Chute Location Option.

        
  • Structural steel construction with zinc prime & powder coated finish
  • interior body widths are 88″(EXT) & 87″(INT) and exterior width is 96″
  • Interior height is 72″ high
  • Floors are constructed of 10GA steel sheet with 3″ structural channel on 16″ centers
  • Posts are constructed of 12GA steel sheet; exterior posts are 5″ formed posts on 36″-48″ centers, Interior posts are 3″ structural channel on 16″ centers
  • Top rails are constructed of 3″ x 3″ x 1/8″ square steel tubing
  • Rear corner posts are constructed of 7GA steel
  • Roofs are constructed of 12GA steel with a 6″ peak
  • Lockable security-style doors with 3″ x 3″ supports
  • Standard 6″ steel ground rollers
Recently viewed Products